Low weight lose product series

Optimizing the ingredients of the magnet, Micro-structure and coating of the surface, our company has developed a series of low- weight- loss magnet , the weight loss of which can be lower than 1 mg/cm² after the corrosion HAST test(130 ℃, 2atm, 95%humidity).

Meanwhile, we work with Institute of Nanotechnology in Zhejiang University to develop the protection technology for the surface of Nano coating. That technology has already been used to produce magnet with high corrosion-resistance.

Low Temp. coefficient product series

LECMAG Magnetic Technology applies itself into the development and stable production for Automotive motor magnet and Wind turbine magnet.  high-consistency and low-temp . coefficient magnetThe high-consistency and low-temp . coefficient magnet of multi-grade and multi-type are already in mass product. As for SHT series wind turbine magnet with big dimension in mass production, the magnetic-flux fluctuation range < ±1%; 120℃ X 2h average heat demagnetization rate < 1%;

As for 38UH-38AH series Automotive motor magnet in mass production, the temperature coefficient of Coercivity in the range of 20-150℃ of 38UH can be down to -0.47%/℃ and it can continue working over 2000 hrs in the cold and hot shock environment of Temp ranging -40℃~160℃.

As for 38AH series product, Temperature Coefficient of remanence in the range of 20-150℃ can be down to -0.09%/℃, and the Max. working temp. can be up to 240℃.

The picture on the right is the micro-structure of 42SHT wind turbine magnet. The particle size is in high consistence, no neodymium rich phase agglomeration among particles, which lays a good foundation for the low temp. coefficient, low weight loss and high-consistence of the magnet.

HREE rare earth-free/HREE rare earth-low product series

We have already mass produced kinds of ( HREE) Heavy Rare earth-free/(HREE) Heavy Rare earth-low magnet; Through Optimizing the ingredient and Cast slice structure, the particle size of the magnet is refined and the micro-structure is also optimized, which decreases the reliance of (HREE) Heavy rare earth—Dy and Te and decreases the material cost for High grade NdFeB magnet . (HREE) Heavy rare earth-free series : N52/N54, 50M, 45H(48H), 38SH(40SH) (HREE) Heavy rare earth-low series of grade 52M, 50H, 42SH

Grain boundary diffusion product series

Grain boundary diffusion technology can reduce the use volume of the (HREE)Heavy rare earth so that it can save the (HREE) Heavy rare earth material effectively, and decreases the production cost of the magnet as well as enhance the comprehensive cost performance of the product.

Aiming at the magnets with same grade, compared with traditional process technology, grain boundary diffusion process technology uses less (HREE) Heavy rare earth and this technology can make the magnet with higher comprehensive cost performance.

With grain boundary diffusion process technology, super-high grade magnet can be made, like 52SH, 50UH, 45EH, and 40AH. HCJ of some magnet(kOe)+(BH)max(MGOe)>78.

Lamination magnet series

Lamination rare earth magnet is proved that it can reduce the eddy current loss for the high-efficiency motors. The reduction of the eddy current loss can decrease the heat and enhance the efficiency. Nowadays, new-energy Auto, aerospace as well as Intelligent industrial robot markets are addicted to pursuing the balance of motor power and calorific value, so the demand of lamination rare earth magnet has kept increasing. With respect to your designing team and project requirement, we can help you to realize the magnetic customization of the following contents by using the licensed process manufactured lamination rare earth magnet in LEC Magnetics:

* Insulation thickness:50μm-100mm

* Insulation layers:2-40 layer(Magnet thickness limits the layers)

* Max working temp. of the magnet:60-400℃

* Temp.Resistance of the magnet surface coating:200-500℃

* Corrosion resistance of the magnet surface coating:Neutral salt spray resistance can be over 1000 hrs and PCT can be over 500 hrs.

We can also provide magnetic assembly, even the complete motor rotor.

LECMAG Magnetic Technologies supplies more advanced product solution for you, and our team of Engineers and Project Managers direct the production of products and assemblies at our facilities. You will receive outstanding support at every stage of your project, no matter what material you choose or how complex your design.

Get a free quote